Bell-gossett P2001406C Series e-1510 Centrifugal Pumps Bedienungsanleitung

Installation, Operation,and Maintenance ManualSeries e-1510

Transportation and StorageInspect the deliveryInspect the package1. Inspect the package for damaged or missing items upon delivery.2. Note any damaged

ExamplesFigure 1: Example of a proper lifting methodFigure 2: Example of a proper lifting method using lifting lugsStorage requirementsIf the unit wil

Product DescriptionGeneral descriptionDescriptionThe pump is a centrifugal, frame-mounted pump. The following pump features make iteasy to install, op

Table notes1. An external flush is required on low pressure systems that contain a highconcentration of abrasives.2. Use packing on open or closed syst

InstallationPreinstallationPrecautionsWARNING:• When installing in a potentially explosive environment, make sure that the motor isproperly certified.•

Guideline Explanation/commentWhen possible, locate the pump below the fluidlevel.This facilitates priming, ensures a steady flow of liquid, andprovides

Check Explanation/comment CheckedCheck that a section of straight pipe, with a length thatis a minimum of five times its diameter, is installedbetween

Typical installation45678109123111213141. Expansion tank2. B&G Rolairtrol® air separator3. Supply to system4. TPV Tank Purge Valve5. B&G Tripl

1. Mount and fasten the pump on the baseplate. Use applicable bolts. Center pump onbaseplate.2. Mount the driver on the baseplate. Use applicable bolt

Pump-to-driver alignmentPrecautionsWARNING:• Follow shaft alignment procedures in order to prevent catastrophic failure of drivecomponents or unintend

Align a standard sleeve type coupling (black rubber sleeve)WARNING:Always disconnect and lock out power to the driver before you perform any installat

121. Amount of Parallel Misalignment2. Straight EdgeFigure 4: Example of parallel misalignmentc) Move or shim the drive unit, if necessary, until the

Commissioning, Startup, Operation,and ShutdownPreparation for startupWARNING:• Failure to follow these precautions before you start the unit will lead

Start the pumpCAUTION:• Immediately observe the pressure gauges. If discharge pressure is not quicklyattained, stop the driver, reprime, and attempt t

NOTICE:• Avoid increased radial load. Failure to do so can cause stress on the shaft andbearings.• Avoid heat build-up. Failure to do so can cause rot

temperatures in the range of 32°F to 190°F (0°C to 88°C), average leakage rates of 60 to80 drops per minute are recommended. However, each individual

MaintenanceBearing maintenanceBearing lubrication scheduleType of bearing First lubrication,assembled pumpsand replacementbearing framesFirst lubricat

Specifications — grease typesPolyurea-based greases Lithium-based greases, NLGI 2Pumps built on or after Dec 1, 2014 use Polyurea-basedgreases. See dat

Do not spread the outer and inner guards more than necessary to remove the guard.It could alter their fit and appearance.3. Remove the capscrew that ho

WARNING:Make certain that the internal pressure of the pump is relieved beforeyou continue. Failure to follow these instructions could result in serio

Table of ContentsIntroduction and Safety...

NOTICE:Protect machined surfaces while you clean the parts. Failure to do so may result inequipment damage.Replacement guidelinesImpeller replacementT

• Recommended rough cut feed rate per revolution is 0.008 in. (0.20 mm) and depth ofcut is 0.050 in (1.27 mm).• Recommended finish cut feed rate per re

2134567891113141617181012151. Impeller2. Vent Plug3. Volute4. Volute Gasket5. Coverplate6. Seal Assembly7. Bearing Frame8. Shaft9. Support Foot10. Sup

2345679181. O-ring2. Coverplate3. For 1-1/4 in. seal: 1-13/32 in. (3.571 cm)4. For 1-5/8 in. seal and 2-2/3 in. seal; 1-1/4 in. (3.175 cm)5. Seal lock

Assemble the packed stuffing box (e-1510-PF)1235 4678111213141620199101517181. Impeller2. Volute3. Volute Gasket4. Coverplate5. Coverplate Capscrews6.

4. Install a flush piping if it is used.5. Install the support foot capscrews and tighten them according to the Capscrew torquevalues table.6. Install

Size Turns past finger tight Approximate torque3/8 in NPT 1.5 to 3 40 (54)1/2 in NPT 1.5 to 3 54 (73)Dealer servicingIf trouble occurs that cannot be r

Product warrantyCommercial warrantyWarranty. For goods sold to commercial buyers, Seller warrants the goods sold to Buyerhereunder (with the exception

Limited consumer warrantyWarranty. For goods sold for personal, family or household purposes, Seller warrants thegoods purchased hereunder (with the e

To make a warranty claim, check first with the dealer from whom you purchased theproduct or call the following number for the name and location of the

Drain the pump...25Remove the hex c

Xylem |’zīləm|1) The tissue in plants that brings water upward from the roots2) A leading global water technology companyWe're 12,500 people unifi

Introduction and SafetyIntroductionPurpose of this manualThe purpose of this manual is to provide necessary information for:• Installation• Operation•

DefinitionsSafety message level IndicationDANGER: A hazardous situation which, if not avoided, will result indeath or serious injuryWARNING: A hazardou

P70642P70643(2) Required(1 Each Side)AlternateLocationP2002458P70820DO NOT RUN PUMP DRY, SEALDAMAGE MAY OCCUR.INSPECT PUMP SEALREGULARLY FOR LEAKS,REP

NOTICE:Never operate a unit unless safety devices are installed. Also see specific informationabout safety devices in other chapters of this manual.Ele

Condition ActionChemicals or hazardous fluids onskin1. Remove contaminated clothing.2. Wash the skin with soap and water for at least 1 minute.3. Seek